"Product Catgeory","pabx system-EPABX" "Product Name","epabx system" "Specification Title","Specification Value" Type,EPABX "No. of Analogue Extensions",128 "Expandable upto",896 "No. of Digital Extensions",16 "No. of Analogue Junction",8 "No. of PRI Cards",1 "No. of PRI Ports/Card",NA "IP Card",YES "If yes No. of IP Cards","Must Indicate" "If yes No. of Channels / IP Card",256 "No. of SIP Extensions",8 "No. of SIP Trunks",8 "Operator Console",1 "MDF( No. of Pair )",400 "MDF( No. of Pair with IPM )",NA "GENERAL FEATURES FOR EPABX SYSTEM: (a) The EPABX system is Digital Microprocessor based stored program control with latest Software Version. It has facility to connect Computer Terminal, Telephone, and Paging System through suitable Interface common to all such devices. (b) The system is capable of working in a suitably ventilated non-air-conditioned environment. System design is immune to noise from various sources like power supplies, lighting system etc. (c) System to ensure a very high degree of availability and maintainability through use of highly reliable components and appropriate structural & functional units. Provision of redundant control units in a suitable configuration is provided as an option. (d) All components are rated for continuous operation of the system. It is designed in such a way that any damage in any circuit/ Subassembly/assembly is self-containing and not propagate to other parts of the system. (e) The EPABX is capable of pulse to tone conversion and vice versa to enable correct operation (originating & receiving calls) with the DTMF and dial pulse signaling having a speed range of 8-12 PPS and break ratio of 50 to 80%. Dialing out to meet following limits. Dial Speed : 10+/0.5 PPS Make/break ratio : 1:2, normal with break period between 65 to 68%. IDP : >550 ms. (f) The equipment is capable of working under the howling line & junction limits as under: i. Extension loop resistance of 1200 ohms for large systems and 600 ohms for small systems. ii. Junction Loop up to 1800 ohms. iii. Insulation lower limit 20 k ohms. (g) Flexibility of opening & closing of limits & modification in class of service is provided. (i) There must be protection of EPABX System from high voltage/current transient occurring on junction lines to the Exchange. (j) All cards of the same type & design are interchangeable without necessitating special adjustments. System to be offered with Hot standby facility if there is provision for the same. (k) Cabinet design is to be provided with adequate ventilation to dissipate heat due to energy loss. (l) The points for connecting supplies, the power supply to the different plug-in cards is standardized & mechanically interchangeable to prevent damage due to accidental interchange of cards. (m) Sub-assemblies & printed cards in the equipment is suitably marked Identification of a type of card in its connector is possible without necessitating its removal. Any plug-in component is marked with sufficient information for its complete identification. (n) All instructions labels or any other marking on the equipment is perfectly legible. (o) Connecting cables between jacks is marked in their extremities with identical designation as on the fixed connecting flanges. (p) Fuses used are with suitable marking for the different rating to enable easy identification and replacement.","In compliance" "SYSTEM FEATURES FOR EPABX SYSTEM : (a) The EPABX System is Digital PCM/TDM (non-blocking) technology. (b) Tone and Ringing: The System to provide the standard tones and ringing current as in the Public Telephone Network as follows : (i) Ringing 75 V AC , 25 Hz. (ii) Ring back tone 400 Hz. 0.4 sec ON, 0.4 sec OFF. (iii) Dial tone 400 Hz modulated by 25 Hz. (iv) Busy tone 400 Hz, 0.75 sec ON, 0.75 sec OFF. (v) Operating Voltage 48 V +/- 4 V DC. (c) The equipment and circuits for tones and ringing are part of main PABX equipment. (d) The equipment is with Automatic Route Selection facility to determine least cost route automatically based on class of service. (e) Extension-to-Extension Dialing: It is possible to establish internal calls automatically by dialing any number without assistance of the attendant. (f) Direct Outward Dialing: It is possible to establish external calls automatically by dialing any number without the assistance of the attendant (subject to class of service). (g) Provision of DID & DISA: It has facility for direct inward dialing and direct inward station access. (h) Direct Outwards Station Access (DOSA): Any Extension can access the trunk lines of the System through personal pass code to make outward calls. All DOSA calls remain in account of that particular Extension. (i) Direct Station Selection (DSS): Just pressing a single key the operator or extension can directly call an extension or access the trunk line without hassles of pressing 3 digits. (j) Multi Level Voice DISA: When ordered as an extra feature/card, this will enable the systems to provide auto attendant service to outside callers to directly access the desired extension by surpassing the operator. The caller is to be step wise guided by multi-level voice messages. (k) Access To Exchange Network: It is possible for an extension to get access to public network with or without the attendant in such cases, facility to exist for the attendant to either dial the required No. or to merely extend the junction to the extension and permit the subscriber to dial the number. (l) Privacy Of Call: Full privacy of conversation is available on all calls whether established directly or by the attendant. A warning tone of a specified frequency is applied when trunk-offering facility is exercised by the attendant on an extension user. (m) Class Of Service: It is possible to allow an extension control over the telephone usage by providing him suitable class of service. (n) The coding technique to be used is ALAW/CODEC per channel. (o) System has provision for Automatic Last Number Redial up to 20 times on Junction Line. (p) During night, when the board is shut, external lines is be linked to any pre-defined extensions. (q) Provision for connecting recorded voice / answering to make available extensions to an incoming call without the help of operator. (r) Flexible Numbering Scheme: System has provision for flexible numbering plan up to four digits for extensions. (s) Trunk Support: The System supports following connectivity to satisfy all type of trunks & tie circuits. Analog for all For ISDN compatibility In case of Small EPABX Systems : ISDN BRI In case of Large EPABX Systems : ISDN BRI & ISDN PRI For Networking Compatibility In case of Small EPABX Systems : Digital ISDN and VOIP In case of Large EPABX Systems : Digital ISDN, E1, E&M and VOIP Generally system supporting ISDN PRI is also compatible to E1 connectivity. (t) Universal Port Configuration: All ports of the System are identical to facilitate flexible configuration of the System as per user needs. (u) Discriminate Ringing: The System supports discriminate ringing to indicate internal & external calls. (v) Multiple Consoles: The System supports multiple numbers of consoles for large EPBAX Systems. (w) Mixed Station Dialing: To support all the features irrespective of type of telephone instruments i.e., DTMF or DECADIC. (x) Versatile ASMDR The System supports ASMDR, which is a call accounting application that can record & print up to at least 3500 calls without dedicated printer. (y) Power Failure Transfer: In the case of power failure all P&T / CO lines become available on the pre-set Extensions. Provision for Availability of Junction Lines are as under: System of 4 & 8 Junctions: Availability of 2 Junctions System of 24 & 32 Junctions: Availability of 4 Junctions System of 64 Junctions: Availability of 8 Junctions (z) Programmable Class Of Service: The System supports programmable class of service for P&T (STD/ISD/LOCAL) dialing as per need. (i) Direct Call Billing In Rupees: The System supports direct call billing (near value) through parallel/serial port printer without computer or through Call billing software with computer. (ii) Call Billing Printout Options: The System supports versatile multiple combinations of direct printout options with total amount viz., Extension wise, Trunk wise. Today's call print out, Group wise printout, Particular date, Particular Month, Particular Time, Particular Phone etc. (iii) Calling Line Identification (CLIP) : This is an optional feature and when ordered it enables the incoming calling No. is displayed on Key/Analog Phone even if the call is transferred by the operator, it is compatible to DTMF (Optional). (iv) Remote Maintenance: The System programming can even be done from remote locations.","In compliance" "EXTENSION FEATURES FOR EPABX SYSTEM : (a) Automatic Call Back: Facility exist for an extension user on encountering a busy signal on a called extension, to invoke the automatic call back feature by dialing a code before hanging up. When both the calling and called parties are free, the call is be automatically put through and in case of no-answer the call may be disconnected after a specified period. This facility is available throughout the network if more than one EPABX are interconnected in a Private Network. (b) Call Forwarding: An extension with this class of service is able to transfer all incoming calls, temporarily to another pre-selected extension. Such requests to be registered by dialing a code followed by the extension No. Facility also exist for cancellation of a request registered earlier. This facility is available throughout the network if more than one EPABXs are inter-connected in a Private Network. (c) Consultation Hold: An extension engaged on an external call (incoming or outgoing) is able to hold the call while making internal call for private consultation. The external subscriber not to overhear such consultation. There must be facility of music during hold condition. (d) Brokers Call: An extension engaged on an external call (incoming or outgoing) is able to hold the call while making another call than alternate between the two. The other party not to over hear such consultation. There must be facility of music during hold condition. This facility is be available throughout the network if more than one EPABXs are inter-connected in a Private Network. (e) Automatic Call Transfer: It is possible for an extension user to transfer incoming calls to another extension with or without help of the attendant. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (f) Executive/Secretary: A combination of call forwarding, consultation & hold to provide for executive to selectively/answer calls. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (g) Executive Over-Ride: There must be facility offering priority to 5 min extensions to over-ride on going conversations. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (h) Access To Paging: Extensions and attendant has dial access to a loudspeaker or any other type of Paging System where such a system exists. (i) Conference Call: It is possible for an extension user (up to a maximum number of 6 to talk to each other at the same time on a conference circuit. One of the extension user or by the attendant may set up the conference call. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (j) Call Pick-Up : It is possible for an extension user to pick-up incoming calls ringing on another extension without the help of the attendant. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (k) Call Re-Routing : It is possible for a call to be re-routed, without help of the attendant, to other pre-defined extensions when certain conditions apply. This facility is available throughout the network if more than one EPABXs are interconnected in a private network. (l) Auto Call Disconnection: System to facilitate to fix the time of call beyond which it will be automatically disconnected. (m) Dynamic STD Lock : The System supports individual extension that can lock outward dialing (STD/ISD/LOCAL) by a personal secret pass code to prevent misuse by others. (n) Paging On Key Phone: The caller can activate speaker phone of the called extension to communicate in urgency in own voice when Extension is idle. (o) Call Name & Extension number on Display (Internal CLI): Name as well as Extension No. of the caller is displayed on the Key Phone, facilitating to respond accordingly. (p) Background Music: The Key Phone user can enjoy the light background music channeled from System When Voice DISA Card incorporated. (q) Auto-Answer / Auto-Off : Key Phone can be programmed for auto-answer after pre-set number of incoming rings. The Key Phone is automatically disconnected when caller disconnects.","In compliance" "ATTENDANT'S CONSOLE FEATURES FOR EPABX SYSTEM: Stand-alone or P.C. based Attendant Console with the following features : (a) The operator console has soft/feather touch keys with easy to view display and busy lamp field for extensions. It has easy handling facility for all internal & external calls. (b) Answering an Incoming Call: Facility exist for answering an incoming call, whether from an internal extensions or external junction. It is possible to identify the type of call that is internal, external line etc., from the call indicator. (c) Call Queuing : All incoming calls are presented to the console in order of the arrival. Facility exist for giving preference to junction calls over calls from internal extensions. (d) Serial Call : Facility exist in Large systems to extend an incoming call as serial call, which is come back to attendant on completion of call and permitting the attendant to route the call to another extension and so on. (e) Call Waiting Display : An indication is be given when there is an unanswered call waiting in the queue. The lamp flashes if number of calls waiting in the queue are two or more or if a call has been waiting for more than a predetermine time. (f) Call Selection : Facility exist to the attendant to select which incoming call to be answered first. (g) Call Hold Facility : It is possible for the attendant to place an incoming junction call on hold pending further processing. (h) Setting Up External Calls : Facility exist for enabling the attendant to set up the external calls for the extensions, which are allowed to access the public network. The attendant may either dial the number himself or merely extend the junction to the authorized extension user. (i) Trunk Offering : The attendant is able to offer an incoming call to busy extension. A tone however, alert the talking parties when the attendant barges-in on a connection. (j) Provision for Remote Supervisor Control. (k) Position Busy : When more than one console is in use. It is possible for a console to prevent further incoming calls from being assigned to it by busying itself. When a console is too busy, all the waiting calls queued for the particular console are transferred to other console/extensions. Incoming calls in cases where two consoles exist are equally distributed. Facility exist during absence of the attendants for incoming external calls to be forwarded to one common or several individual extensions. (l) Night Service : It is possible for all incoming calls to be transferred to certain pre-fixed extensions, in case this option has been exercised during the night. (m) Head Phone Connectivity : The operators can plug-in headphone to handle the call traffic efficiently while keeping her/his hands free for other jobs.","In compliance" "SERVICE OBJECTIVES FOR EPABX SYSTEM: Following service objectives are to be met : (a) Under overload conditions, the lost call figure applicable is one in 200 for extensions to extensions call and one call in 100 for junction calls, overload being defined as 10% increase in occupancy of speech network and simultaneous 25% increase in the number of calls. (b) The selection time under full load is defined as the time interval between the instant at which the required information for selection of the outlet has been received at the inlet and the instant at which outlet is ceased not to exceed in 99% of the cases under traffic overload 1.5 seconds. (c) The assumption to be made while deciding the dimension of the links, junctions and attendants console are following : i. Total originating & terminating traffic per extension (including junction traffic) 0.2 erlang during peak busy hour. ii. Total junction traffic per extension 0.1 erlang during peak busy hour. iii. Average holding time of calls 0.90 seconds. iv. The switching network provides access to the links & junction on fully non-blocking basis. v. The equipment design is such that any special case and precaution on the part of maintenance personnel are kept to an absolute min. And no preventive maintenance is required. vi. The System has inherent capability to monitor its own performance and to detect, analyze and locate faults. vii. Fault repair at site normally consist of only replacing the faulty card or plug-in modules. viii. The System has remote maintenance facility.","In compliance" "Inbuilt Voice Mail for EPABX Ststem",Yes "Call Buffer Memory for EPABX System",5000 "General Features for Hybrid IP PABX System : (a) Hybrid IP PABX is designed with core IP Switching platform and has facility to connect Analog, Digital and IP Phones on same platform. (b) Hybrid IP PABX also work as Remote Unit in case of customer's requirement of multi office connectivity with centralized PBX at his head office. (c) Hybrid IP PABXs is capable to connect maximum number of Analog/ Digital Phones as required on IP switching network along with IP Phones. (d) Being a hybrid switch, it offers the same set of capabilities to both Analog Phones and IP endpoints and offer intelligent networking which delivers consistent communication system features, services and application over any media or transport to all users across the enterprise, regardless of their locations. (e) System supports IP SIP hard Phones, IP SIP soft phones, Analog phones with CLI, Digital Phones, Fax, Modems etc. (f) It supports multi location distributed processing architecture with anywhere switching. It is capable to connect various offices situated at distant locations via Internet (IP) and establish cost effective voice communication on IP. While the distant offices to be connected through IP, the communication within the office is possible on normal Analogue phones for making internal and external (PSTN) calls. (g) It is flexible enough to become a pure IP solution, an all digital/Analog solution or a combination of both. (h) The IP PABX system is capable to support following trunk interfaces/protocols (i) Analog PSTN Trunk - The system has analog PSTN trunk interface to connect normal CO lines for making and receiving calls. (ii) The system also supports DID features for both analogue and digital trunks. (iii) Analogue or Digital Tie Trunk - The system is able to support analogue 2/4-wire E&M Tie trunk, Two-Way-Trunk and digital E1 Tie trunk to support the private networking. (iv) ISDN-PRI - The system is able to provide ISDN-PRI trunk to support the private networking. (v) Magneto Trunks (i) The system has distributed architecture and is capable to use embedded server up to 2000 ports requirement. For higher capacity requirements or multi office connectivity, Hybrid IP PABX to use Industry standard server (j) The system has suitable power supply architecture, wherein each peripheral card of the system has its own power supply unit capable of working with direct 48V DC input and generating the required voltages for any of the card. (k) All critical resource elements of IP PABX (call server, hard disks, data bases, IP interfaces, DSP resources, clocking sources, Processor, RAM, Tone generators, Power supplies, Ring generators, Resources like DTMF receivers, Tone detectors etc. may be redundant in hot-standby mode. (l) The IP PABX system supports the following standards for voice encoding - (i) G.711A (ii) G.711µ (iii) G.723 (5.3 bit rate and 6.3 bit rate) (iv) G.729 (m) The system is suitable to accommodate both Decadic Pulse (DP) and DTMF telephones. The system supports outgoing DTMF transmission even from Digital phones. (n) System supports VOIP solutions as an integral part of the system. The VOIP is implemented through plug in interface boards in any slot of the system.","In compliance" "System Features for Hybrid IP PABX System : (a) The IP PABX System is suitable for flexible numbering scheme. It is support at least 6 digits numbering scheme. System also allow mixed numbering scheme. (b) System has abbreviated dialing feature configurable for system wise and individual user basis. (c) Caller ID information for both internal and external callers (over Analogue, ISDN PRI) is available to endpoint users. It is possible to capture the CLI coming from the digital and analog trunks in the Network and display the same on following : (i) IP Phones (ii) Digital Phones. (iii) Analog Phones with DTMF and FSK CLI with Name unit (inbuilt CLI unit). It is possible to provide CLI on all analog extensions simultaneously without any limitation on the number of extensions on which this facility would be available. (d) Every subscriber has his own authorization code to make outgoing calls thereby ensuring no misuse of the system. Unique authorization codes is possible for every subscriber & the user to have a complete flexibility to dial his identification or authentication code from any location & thus utilize all his facilities from there. (e) Automatic call back for any of the dialed extension within the exchange in case of busy. (f) Direct seizure of PSTN junction using a code or a key of digital phone. (g) Reservation of access to PSTN junction line for certain user. (h) Limitation for certain user to access PSTN junction line depending on time of the day. (i) Fully Restricted Extensions - Extensions must be able to be barred from all forms of outgoing access, except calls to Emergency Service like Helpdesk, Fault Control, Fire service through class of service programming. This will restrict the extension to receiving incoming calls only. (j) Time Based disconnection on PSTN calls which is be user group based. (k) The system may have option to support IP connectivity to third party applications like call billing system, voice mail, IVR (Interactive Voice Response) System etc. (l) Class of restriction facility to define different class of call origination and termination facilities. (m) Call Waiting - System allow users to have "Call waiting" for internal caller and external caller or operator. Subscribers with digital or IP- telephones with display is able to override an ongoing call for a waiting call. In the busy state, the callers receive the call connect signal, the subscriber receives an alerting tone and the caller ID is shown on the display. Without terminating the existing call, it is possible to take the waiting call and toggle between the two calls. The caller hear a call waiting tone in case to be informed about his call waiting. (n) System has built-in music-on-hold facility. The system provide internal/external music and recorded announcement information to callers on hold. (o) Voice Prompts and Announcement - The system supports a plug-in voice announcement board with minimum 30 announcements. (p) Call Detail Recording - System supports versatile call charging system. Details of extension numbers date, time, called number, duration of call and call charges to be provided. The system has an inbuilt billing system, which is capable of calculating the call charges without the need for any additional external hardware or software systems. (q) Call Budgeting - The system has call budgeting feature, wherein the call charge budget for each extension of the system can be defined and if for any user, the budget exceeds, all outgoing trunk calls will be barred. This feature is inbuilt in the system. (r) Least Cost Routing - The system has inbuilt Least Cost routing (LCR) which can be configured as Dialed number based or Time based or call charges based. (s) The System has option of Auto attendant facility. (t) Multiple Operator Positions. - Multiple Operator positions to be provided, and Exchange lines and functions may be grouped to be handled by one or more operator positions. The system has a provision to support at least 64 operator consoles. The operator consoles to be equipped with PC based consoles with headgears. (u) Conference : The system supports minimum 12 party conferences. This could be in a single conference of 12 members or four conferences of 3 members or in any combination thereof. (v) The system has the function of gateway and gatekeeper for IP telephony. The hardware should be on board capable of going into any universal slot. (w) The system supports mix-mode dialing. The system automatically detect the type of analog phone connected to the subscriber card and support PULSE/DTMF dial without changing the parameters in the switch. (x) The system has provision for remote logins for maintenance. These Logins are password protected. Also there it is possible to create different maintenance logins with different privileges. (y) The system administration and maintenance should be using GUI based software. (z) Closed User Group : The system support at least 32 closed user group with maximum of 50 subscribers in each group.","In compliance" "Extension Features for Hybrid IP PABX System : The following features are available : (a) Extension to extension calls, Operator assisted calls (b) Direct inward dialing (DID), Direct outward dialing (c) Programmable Class of Service features for local/STD/ISD dialing as well as for system features with dynamic locking facility. (d) Discriminative ringing for internal, external and VIP calls. (e) Abbreviate dialing - Individual extensions are able to at least program 10 abbreviated call numbers for regularly called numbers (f) Call forwarding - The system supports the following types of call forwarding to be activated in any combination : (i) for all calls (ii) When busy : for internal calls or external calls or both (iii) When No Reply : for internal calls or external calls or both (iv) When Not Registered : for internal calls or external calls or both Calls can be forwarded to a selected internal extension number, to the attendant queue, a specific attendant, or to voice terminal in the public network. The forwarded number can be different for internal and external calls. (g) Call Pickup - The system is support the following types of call pickup : (i) Group Call Pickup (ii) Directed call pick-up (h) Call Back - The system is support Call Back on Busy and Call Back on No Answer. (i) Call Transfer - (i) Transferring external calls (ii) Transferring internal calls (j) Camp On - (i) Camp On Busy (ii) Camp On Idle (k) Call Parking - It is possible to park calls and retrieve from both analog and digital/IP extensions. (l) Line - lockout (m) Trunk camp on, Wake up alarm, Do not disturb (n) Last number redial (o) Voice mail interface server (p) Emergency Call - The system has the facility for the user to broadcast simultaneously on at least 5 end point users irrespective of their state in event of any emergency through message dialing a feature code. (q) Missed/Dialed/Received Call Lists - It is be possible to view at least last eight dialed/received/missed calls on display equipped terminals. (r) Last Caller Call back - For an analog subscriber without CLI phone, it is possible to dial the last incoming caller, by dialing a specific code. This would enable the analog subscriber to call back any missed call on his/her extension. (s) Hotline - Direct inward system access (t) Password Display Suppression - When a password is entered in a display equipped terminal the display should suppress the digits so that no one present can deduce the password. (u) Personal Identification Number - This feature is also called as Floating Password. Through this feature subscribers is able to go to any extension in and across the network and make that extension as his extension for a Call or for certain time period. (v) Password Control - It is possible to assign Passwords to telephone from both Maintenance Terminals as well as telephone to prevent misuse of telephone. (w) Virtual Telephony - It is possible to give subscribers a virtual account code, which can be used for making outgoing calls from any extension. All such calls made are to be accounted to the virtual account. (x) Hunt Groups - It is possible to have both Cyclic and Linear Hunting of extensions. (y) Howler Tone - It is possible to give a howler tone on the extension in case the handset is kept off hook after a timeout. (z) One Number Service - The system supports One Number Service. This feature allows the calls coming in to extension to ring after administered numbers of rings (follow me) at a predefined Mobile phone number or PSTN Number. It is then be possible to use the predefined handset as a remote extension. (aa) Add on conference (three parties) (bb) Preset Conference Calls: It is possible to dial out a pre-defined group of participants/numbers (minimum 30) by simply pressing the pre-assigned key on the digital phone or by code from any of the analog phone. It is also possible to have multiple such groups. Additionally, each preset conference must have its own unique dial number. When this group number is dialed, all the number stations will ring simultaneously. As members join the conference, all actively-participating members will hear a warning tone indicating that another participant has entered the conference. Stations that go un-answered will continue ringing without disturbing the conference until the ring time out is completed.","In compliance" "Voice Mail for Hybrid IP PABX System : System to be provided with in-skin voice mail system or Standalone (Integrated with software) or PC based voice mail system. The Voice Mail System with necessary Hardware and Software to work in conjunction with the Hybrid PABX is part of the system. The Voice Mail has all the traditional voice mail features as follows : (a) To record, delete, play, forward and reply to voice messages. (b) To send group messages for many mail boxes simultaneously. (c) Personal Greetings (Name or Mail Box Number). Users are able to record/change their names, greetings etc from their phone itself (d) Different Greetings to External & Internal Caller. (e) Password or Personal Identification Number (PIN) to access VM boxes. (f) To select next message and previous message. (g) The system inform/indicate the availability of messages in the Mail Boxes to the users either - (i) Audibly - Tone/Voice Prompt. (ii) Visually - by illuminating the message waiting lamp on the telephones. (h) Programming/reconfiguration and creation of mailboxes of the VM system is possible by utilizing the maintenance administration terminal. (i) Administration Interface- The system provides direct access to the system database through a PC interface, from which traffic and usage reports can be generated. (j) Automatic Message Scan - The system allows the subscribers to scan all message headers and/or messages by simple feature codes. (k) Call Answer - The system provides the facility of answering calls and recording messages for unavailable or busy subscribers. It also enable the subscribers to listen to or intercept call answers as they are being left by callers.","In compliance" "No. of E1 Cards",NA "No. of E1 ports / Card",NA "Hot Standby CPU",NO "Hot Standby PSU",NO "Hot Standby CPU (Hybrid IP PABX)",NO "Power Requirement","230 V, 50 Hz" "Provision for Inbuilt Battery Charging Arrangement for providing Battery Backup",2 FCBC,NO "If yes, Rating of FCBC (48V)",NA "Protection against over current and accidental reversal of polarity on the input side and against over current and over voltage on the output side",YES "Availability of additional SIP License in multiple of 16 users",NO "If yes,No. of additional SIP License in multiple of 16 users",1 "Radio Interface Card/Gateway",NO "If yes, No. of Radio Interface Card/Gateway",NA "GSM Card/Gateway",NO "If yes, No. of GSM Card/Gateway",NA "E&M Card/Gateway",NO "If yes, No. of E&M Card/Gateway",NA "Push Button Telephone with CLI",YES "If yes, No. of Push Button Telephone with CLI",128 "Push Button Telephone with CLI & Speaker Phone",YES "If yes, No. of Push Button Telephone with CLI & Speaker Phone",64 "8 Keys IP Phone with Display",NO "If yes, No. of 8 Keys IP Phone with Display",NA "12 Keys IP Phone with Display",NO "If yes, No. of 12 Keys IP Phone with Display",NA "Digital phone with 2 Line Display 32 character & 8 Programmable Keys",NO "If yes, No. of Digital phone with 2 Line Display 32 character & 8 Programmable Keys",NA "Digital phone with 2 Line Display 32 character & 12 Programmable Keys",YES "If yes, No. of Digital phone with 2 Line Display 32 character & 12 Programmable Keys",16 "TEC approval as per the latest TEC specifications",YES "TEC approval Certificate no. & Date",SV9100OFFICETECNEWDELHI "Operating Temperature Range","0 TO 60" "Operating Humidity (RH)","5 TO 95" ""Availability of Test Reports from Central Govt / NABL approved / ILAC acredited lab to prove conformity to the specification including Environmental Test Sequence. i. Cold Test : At zero Degree C for 2 hrs. as per IS 9000/ Pt 2/Sec 4/ ii. Dry Test : At 45 Degree C for 16 hrs. as per IS 9000/ Pt 3/Sec 5/1977 iii. Damp Heat(Steady State) Test: At 40 Degree C & 95% RH for 2 cycles as per IS 9000/Pt 5/Sec 1/1977 After completion of environmental conditioning sequence as specified and recovery of 1&1/2 hours, the functional performance/features of EPABX sytem/Hybrid IP PABX System shall be checked"",YES "Avaibility of operation and maintenance manuals",YES "Test Report No.",PRTL(N)/90(4)-(2015-16)/C0048 "Test Report Date",29.4.2015 "Name of the Lab","ELECTRONIC REGIONAL TEST LEBORATARY NEW DELHI " "Installation and Commissioning",YES Warranty,1