1-800-419-3436 / 1-800-102-3436 
Support Desk
×
All the transactions performed on 2.0 is available here. To access Market click "Home".
The Mobile Weigh Bridge Testing Kit is designed specifically for Calibration of Weigh Bridges. It comprises of RRSL Calibrated Weights in assorted sizes totalling 5000 Kgs, Hydraulically operated Wing Body, 4 nos. Hydraulic Stabilizers with electronic vehicle auto levelling system, an Articulated Knuckle Boom Crane of 8 Ton-Meter Lifting Moment, and the Carrier Vehicle. The RRSL Calibrated Weights are placed inside the Hydraulic Wing Body made of reinforced MS sheet of 3mm side, 2mm Lid and 5mm Bottom Plate. These weights are lifted and positioned with the help of the Knuckle Boom Crane. The entire unit is mounted on an ARAI certified BS-IV compliant Chassis with Cabin and External PTO Unit having 16T GVW and minimum 130HP Engine Power, provided by the Purchaser at its own cost at our works in Delhi NCR for fabrication and installation of the Mobile Testing Kit. Transit Insurance Charges for final transport till consignee location shall be payable Extra on Actuals by the Purchaser..
| Other Specifications Download Specification | |
|---|---|
| Confirmity To Standards For Power Driven Mobile Cranes IS : 4573(1982) With Latest Amendment. | Yes |
| Engine Capacity Of Chassis | 5675 CC |
| Chassis Certification | ARAI |
| Make Of Chassis | TATA |
| Design Of Truck Chassis | Full Frame chassis |
| Type Of Chassis | Chassis with facecowl |
| Chassis With Built Up Cabin | Yes |
| Chassis Model No. | TATA LPK 1613-36WB TIPPER CHASSIS |
| Type Of Fuel | Diesel |
| Vehicle Emission Complaince | BS-IV |
| Engine Power BHP@rpm | 145 BHP@rpm |
| Engine Torque Max,@ Rpm | 490 NM @ 1400-1800 RPM N-M@rpm |
| Engine Aspiration | Turbocharged Intercooled |
| No. Of Cylinder In Engine | 6 |
| Fuel Tank Capacity | 160 litres |
| Length Of Chassis | 6045 mm |
| Width Of Chassis | 2836 mm |
| Height Of Chassis | 2430 mm |
| Mobile Kit Equipment For Calibration Of Weighbridge | Yes |
| Hydraulic Operated Wing Body Constructed On Chassis Comprises Of Top Two Part Lids Normally Closed In Transportation Position | Yes |
| Hydraulic Operated Wing Body Openable Parallel To Side Walls Of The Fixed Part Of The Body To Allow Full And Unhinderd Access For The Hydraulic Cranes | Yes |
| Type Of Crane | Truck Mounted Fully Mobile Full Slewing Cranes |
| Mode Of Operation Of Crane | Fully Hydraulic and Foldable |
| Feature Of Crane | Kunckle Boom with Articulated and Telescopic Boom in line with slew centre of the vertical axis , to be folded on side of chassis with booms folded in between of twin column over the slew in transport Position permitting self loading on truck. |
| Lifting Moment Of Crane | 8000 Kgm |
| If Others Please Declare Lifting Moment Of Crane Otherwise Put NA | NA Kgm |
| Lifting Capacity | 1.0 Tonne at 8.0 meter radius with 85 percentage of tipping Load |
| If Others Please Declare Lifting Capacity Of Crane Otherwise Put NA | NA Ton. |
| Boom Length ( Measured From Slew Centre ) | 8 Metres |
| Crane Mounting Behind Driver's Cabin Truck Chassis Occupy Lateral Space Less Than 1.5( +-10%)meters | Yes Metres |
| Slewing ( Continuous In Both Direction) @ Rpm | 0.5 rpm |
| Hoisting Through Hydraulic Winch To Be Supplied With Equipment | 1 Tonne on Single Fall snatch block |
| Wire Rope Diameter ( Non Twisting Type ) | 8 mm |
| Hoisting Speed | 3 metres/min |
| Material For Rope Drum | Mild Steel Confirming to IS 226 : 1975 or IS 2062 :1980 with latest amendment |
| Factor Of Safety For Running Rope And Standing Rope In Service Condition | 4 |
| Factor Of Safety For Running Rope And Standing Rope In Erection Condition | 3 |
| Diameter Of Drum | 300 mm |
| Diameter Of Pulley | 190 mm |
| Derricking From Horizontal ( 0 Degree) To Full Elevation In Minutes | 1 minutes |
| No. Of Outriggers With Hydraulics Out And Hydraulics Down And Reverse Movement | 4 |
| Type Of Outrrigers | H-type |
| Outriggers Must Spread 4 Meter Min. With Sufficient Penetration Of Outrigger Below Level Ground At Leat 200 Mm With Enough Power To Lift All Wheel Of Fully Loaded Vehicle Off Firm Ground . | Yes |
| Auto Levelling System To Automatically Command The 4 Nos. Outrigger To Level Vehicle With Single Push Button | Yes |
| Wing Body With Available Drawing And Detailed Information Must Be Hydraulic Operated | Yes |
| Hydraulic Winch Capacity On Single Fall | 1000 Kg |
| Standards Weight To Be Supplied And Weight Must Be As Per Schedule Of Standards Weights And Measures Rule 1987 With Latest Amendment. | 1000 kgs (4 Nos.), 500 kgs (1 Nos.), 200 kgs (2 Nos.), 50 kgs (2 Nos. ) |
| Housing Of All The Weights Are To Be Safely And Securely Housed In Fixtures , Bolted To Chassis Deck To Ensure That No Weights Slides During Transporattion | Wooden Fixtures |
| The Wing Body Shall Be Made From MS Sheet, Duly Reinforced With Suitable Channels And Angles To Ensure Rigidity Of The Wing Body .MS Sheet Thickness (mm) | 3.0 mm |
| The Bottom Plate / Deck Shall Be Made From 5 Mm Steel Chequered Plates , Provide Non Slip Flooring | Yes |
| Control For Wing Body Shall Be On Vehicle Rear /the Slew Column Near The Elevated Operator Seat To Ensure Full Visibility Of Wing Body To The Operator | Yes |
| Gradeability Of Chassis( %) | 20.9 % |
| Ground Clearance | 248 mm |
| Wheel Base With ± 200 Mm Tolerance | 3580 mm |
| Kerb Weight | 5140 Kg |
| Gross Vehicle Weight Of Chassis | 16200 Metric Ton |
| No Of Axle | 2 |
| Type Of Front Axle And Suspension System | Heavy Duty Forged I-Beam Reverse Elliot Type and Semi-Elliptical Leaf Springs |
| Type Of Rear Axle And Suspension System | Single Reduction, Hypoid Gears, Fully Floating Axle Shafts and Semi-Elliptical Leaf Springs |
| Type Of Vehicle Tyre | Bias |
| Size Of Front Tyres | 10 X 20 - 16 PR mm |
| Size Of Rear Tyres | 10 X 20 - 16 PR mm |
| Size Of Wheel | 7.5 X 20 mm |
| Chassis Transmission System | Manual |
| Type Of Steering | Power Assisted |
| Turning Radius | To be Declared mm |
| The Crane Shall Be Provide With Limit Switches Or Stops To Prevent Over Winding On The Hoist Motion And Over Derricking Beyond Prescribed Limit | Yes |
| Hydraulic System Shall Comply With IS 4573 With Latest Amndmt Ensuring Safety While Lowering , Raising ,Holding Load , Slewing Etc. | Yes |
| All Safety Features : Interlocks To Ensure Crane Booms , Slew Do Not Operate And Wing Body Does Not Open Until Outriggers Are Deployed And Vice Versa ,Single Push Leveling Button , Interlocks To Ensure That The Wing Body Does Not Close Unless The Crane Is Fully Loaded, Lock Valve On All Cylinders ,Overload Cut Off Audio Visual Signal Must Be In Operator Cabion At Slew Superstructure , Hand Operated Pump To Stow Down Crane In All Movement , Outriggers And Winged Body In The Event Of Main Pump/engine Failure | Yes |
| Hook Attached To Winch Shall Be Designed For Safe Working Load Of 2.0 Tonne And Shall Be A Integral Part Of Crane | Yes |
| Hook Must Be Certified By ISS/IEC Or Any Other Certified Agency Or Standards | Yes |
| Standard Tool Box | Yes |
| List Of Items In Tool Box | Standard Tool Kit |
| Operating And Maintenance Manual 3 Set | Yes |
| Spare Parts Catalogue | Yes |
| Availability Of Drawing | Yes |
| Availability Of Tets Reports For Functional Test,Overload Test,Testing Of Indicators,Stability Test,performance Test,Travelling Testas Per IS 4573 With Latest Amendment From Any ILAC/NABL Accredited/Central Gov. LAB. | Yes |
| Warranty Time | 12 Months |
| Battery Warranty | 12 Months |
| No. Of Free Service | 3 Nos |
| Transportation Charge In Rupees Per Km | 18 Rs/Km |
Price Dekho Price List in india© 2018 GeM All rights reserved.
