Upper Material PU coated fabric / textile for main part of upper, matching fabric mesh for collar, plug and parts of quarter foam inside collar and tongue.Lining Materials - Quarter lining and tongue lining of mesh looking fabric Skin fit.Shape and Design Laced design of boot upper--With tongue and plug-Two colour look, general appearance of greenish brown Nordic forest look-Visible part of lining is matching the upper. Soling Pattern1. The soling shall not include continuous lateral tread patterns or any other features, such as sharp corners at the base of the sole pattern, which may accelerate or cause premature crack formation. 2. The design should be such that the sole will have adequate skid resistance with cleat heightof minimum 5 mm.3. The sole should be of bucket type with wall height more than 20 mm at toe and more than 30mm at heel.The sole will be formed by Direct injection Process on the lasted upper available in Size 5-12. As per Maharashtra Police Specification..
Other Specifications Download Specification | |
---|---|
Conforming To FDDI (FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE, A - 10 / A, Sector-24, NOIDA) Specification No. FDDI/SPEC/Jungle Boot/08:2014 (Revised), Approved By MHA Vide Their Letter No-U.II-98(Spec)/2012-13-Prov-9775 Dated 10/12/2014, And As Per Following Technical Requirements | YES |
Size | 8 |
Colour | Olive Green |
Mass Per Pair For Size-8 Shall Be 750 To 850 Gms (with Increase Or Decrease Of 50 Grams For Each Bigger And Smaller Size Respectively) | YES |
Leg Height For Size-8 Shall Be 160 Mm (with Increase Or Decrease Of 2 Mm For Each Bigger And Smaller Size Respectively) | YES |
Sole | Direct Moulded Polyurethane |
Minimum Thickness Of Sole | 4 mm |
Cleat Height | 2.5 mm |
Thickness Of Sole When Measured At Forepart From Outside With Side Wall | 20 mm |
Thickness Of Sole When Measured At Waist From Outside With Side Wall | 16 mm |
Thickness Of Sole When Measured At Heel From Outside With Side Wall | 35 mm |
Colour Of Sole And Toe Cap | Brown ( For Brown Boots ) |
Upper Material | Upper shell consist of Polyester viscose fabric,Water Repellent as an outer layer and 100 % non-woven Nylon (cambrille type) lining as an inner layer. The two fabrics shall be adhered together with flexible adhesive and polyurethane foam of 5 mm thickness. |
Blend Composition Of Polyester Viscose Fabric Water Repellent | Polyester-80% Viscose-Remainder |
Binding Material Of Polyester Blended Fabric, Black Having Blend Composition Of Polyester-67%, Cotton-33% & Confirming To IS:15852-2009 For Colour Fastness To Light,washing & PH Value | YES |
Insocks | Covered with cambrille type non woven material black |
Thermoplastic Toe Puff And Counter Stiffner Thickness When Extacted From Boot Shall Be 1.7 Mm To 1.9 Mm | YES |
Full Chrome Leather For Toe Cap And Arch Piece Confirming To IS 5677-1986 For Heat Resistance, Colour Fastness To Rubbing Crocking, Solvent Extractable Substances, Water Soluble Matters, Chromium Contents & PH Value Of Water Soluble | YES |
Thickness Of Full Chrome Leather For Toe Cap And Arch Piece Shall Be 1.2 Mm To 1.8 Mm | YES |
Length Of Nylon Laces | 160 cm |
Width Of Laces | 6 mm |
Mass Per 10 Pairs | 125 g |
Breaking Load Of Laces ( 20 Cm Between Grips ) (Test Method- IS: 1969) | 750 |
Dye Fastness To Light (Test Method- IS: 2454) Shall Be Above 4 | YES |
Dye Fastness To Washing Shall Be Above 4 (Test Method- IS/ ISO 105-C10: 2006) (Test Condition As Per Table-2, Test Number-C(3)) | YES |
PH Value Of Aqueous Extract Shall Be 6.5 To 8.5 | YES |
Sewing Threads | Polyester Sewing thread confirming to IS 9543-1980 (Variety No- 7) |
Availability Of Test Report From NABL/ ILAC Accredited Or Central Government Lab To Prove Conformity Of Products To The Specification. | YES |
Test Report No. | A1710211A |
Test Report Date | 10.11.2017 |
Name Of The Lab | ATHARVA LABORATARIES PVT LTD |
Address Of The Lab | Noida |
Test Reports To Be Furnished To Buyer On Demand | YES |