1-800-419-3436 / 1-800-102-3436 
Support Desk
×
All the transactions performed on 2.0 is available here. To access Market click "Home".
AARPEE Make High Precision, High Production All Geared SS- SC Lathe Machine Model KRS-25C/150 has a streamlined modern outlook and contain all the features normally expected in superior quality machines, where precision is required along with stock removal. All the castings are of close grain cast iron conforming to IS-210 and are amply proportioned to withstand stress without distortion. The shafts are of special quality steel and are having ground finish. All the bearings shafts and gears of the main assemblies run in oil bath. Over 1000 working machines all over India have proved their quality, reliability and accuracy, thus provide utmost satisfaction to the buyer.
| Other Specifications Download Specification | |
|---|---|
| Lathe Machine Confirming To IS 6893-1988part 1 With Latest Amndmt. | Yes |
| Lathe Machine Confirming To IS 210 :1993 With Latest Amndmt. | Yes |
| Manually Operated Lathe | Yes |
| Geared Mechanism | Yes |
| Distance Between Centers (mm) X Swing Over Bed (mm) | 2000 x 500 |
| Type | Standard |
| Distance Between Centres | 2000 mm |
| Swing Over Bed | 500 mm |
| Center Height | 250 mm |
| Swing Over Cross Slide | 240 mm |
| Swing Over Carriage Wing | 350 mm |
| Swing In Gap | 690 mm |
| Width Of Gap In Front | 225 mm |
| Type Of Bed | GAP BRIDGE STRAIGHT |
| Length Of Bed | 3160 mm |
| Width Of Bed | 325 mm |
| Gap In Bed | 345 mm |
| Rapid Transverse Of Saddle | 0 mm |
| Rapid Transverse Of Cross Slide | 0 mm |
| Maximum Feed Force | 3000 N |
| Maximum Facing Diameter | 600 mm |
| Maximum Weight Of Workpiece That Can Be Held Between Chuck And Supported By Live Centre | 250 kg |
| Maximum Weight Of Workpiece That Can Be Held Between Chuck And Supported By Dead Centre | 300 kg |
| Torque ,Maximum On Spindle | 6 Nm |
| Type Of Spindle | METRIC |
| Size Of Spindle | 165 mm |
| Type Of Spindle Nose | A2 6 |
| Taper Bore In Spindle As Per IS 2582-1972 With Latest Amndmt. | METRIC |
| Taper Bore In Spindle Sleeve As Per IS1715-1986 With Latest Amndmt. | MT-4 |
| Bore In Spindle | 53 mm |
| No. Of Spindle Speed In Forward Direction | 8 |
| No. Of Spindle Speed In Reverse Direction | 8 |
| Spindle Speed Range In Forward Direction | 45-1000 RPM |
| Spindle Speed Range In Reverse Direction | 45-1000 RPM |
| Type Of Chuck | 3 Jaw Self Centered |
| Diameter Of Chuck ,Maximum | 200 mm |
| Diameter Of Chuck ,Minimum | 200 mm |
| Travel Of Cross Slide | 300 mm |
| Travel Of Top Slide | 150 mm |
| Type Of Tool Holder | FOUR WAY SQUARE |
| Tool Shank Size As Per IS 1983:1958 With Latest Amndmt.(mm X Mm) | 25 X 25 |
| Tail Stock Sleeve Diameter | 60 mm |
| Tail Stock Spindle Taper As Per IS 1715:1986 With Latest Amndmt. | MT-4 |
| Maximum Offset Of Tailstock On Either Side Of Center Line | 10 mm |
| Sleeve Travel Type ( Tail Stock) | Manual |
| Travel Of Sleeve | 200 mm |
| Lead Screw Diameter | 35 mm |
| Lead Screw Pitch | 6.3 mm |
| Lead Screw Feed Range ( Longitudnal Mm/min) | 0.06-1.72mm/rev |
| Lead Screw Feed Range ( Cross In Mm/min) | 0.03-0.86mm/rev |
| Metric Thread Range In Mm | 0.5 - 14 MM |
| British Thread Range In TPI | 2- 60 TPI |
| Module Of Thread | 3.5 mm |
| Diameteral Pitch | 160 mm |
| Rapid Traverse Motor Power In Kw | 0 kw |
| Type Of Cooling | AIR COOL |
| Coolant Pump Output As Per IS 2161 :1962 With Latest Amndmt. | 0.1 kw |
| Coolant Pump Speed In Rev/min | 2700-2800 RPM |
| Coolant Pump Discharge At Maximum Working Height As Per IS 2161 :1962 With Latest Amndmt.in L/min | 35-40 |
| Type Of Lubrication | OIL BATH |
| Length Of Lathe Machine | 3370 mm |
| Width Of Lathe Machine | 930 mm |
| Height Of Lathe Machine | 1275 mm |
| Weight Of Lathe Machine With Electrical And Standards Accessories | 2200 kg |
| Noise Emitted By Machine As Per IS 10998:1984with Latest Amndmt. | 85 dB |
| Mechanical Guarding As Per IS 9474 :1980 With Latest Amndmt. | Yes |
| Colour Of Lathe Machine As Per IS 5 :1978with Latest Amndmt. | APPLE GREEN |
| In Possession Of Technical Evaluation Report As Per IS :11118 | Yes |
| Lead Screw -Ground Profile& Pitch Accuracy 0.03 Mm Over A Length Of 300 Mm. | Yes |
| Machine Confirming Full Power Cutting Load Test To Full Length Turning Capacity Of Machine | Yes |
| Lubrication System Requirement As Per IS:11118 | Yes |
| Cooling System Requirement As Per IS :11118 | Yes |
| Positioning Accuracy Meets The Minimum Requirement As Per IS:1878 For Cumulative Error | Yes |
| Positioning Accuracy Meets The Minimum Requirement As Per IS:1878 For Repeatibility | Yes |
| Positioning Accuracy Meets The Minimum Requirement As Per IS:1878 For Backlash | Yes |
| Positioning Accuracy Meets The Minimum Requirement As Per IS:1878 For Minimum Possible Requirement | Yes |
| Geometric Accuracy Test Of General Purpose Parallel Lathe Machines As Per IS 1878-1971 With Latest Amndmt. | Yes |
| Geometric Accuracy Test Of Precision Lathe Machines As Per IS 6040-1972 With Latest Amndmt. | Yes |
| Machine Bed & Tail Stock Casting Grade Confirming To FG-260 With Hardness 180-230BHN As Per IS 11118-1997 With Latest Amndmt. | Yes |
| Tailstock Sleeve Case Hardening Steel 15Ni7Cr4M02 ,, Hardened And Ground To A Hardness Of 58-62 HRCas Per IS 1118-1997 With Latest Amndmt. | Yes |
| Head Stock Drive Gears Confirming To Alloy Steel Material Specification 15 Ni 7 Cr 4 M02 , Hardened 58-62 HRC And Profile Ground With 0.8 Micron Surface Roughness Ra Value | Yes |
| Main Spindle Confirming To C2R Grade Forged Steel And Hardened 58-62 HRC. / Ground With 0.8 Micron Surface Roughness Ra Value | Yes |
| Main Spindle Bearing Confirming Pre-loaded GAMET/TIMKEN Make Spindle Bearing High Precision Class Double Row Taper Roller Bearings At Front & Single Row Taper Roller Bearing At Back | Yes |
| Machine Confirming Dynamically Balanced Spindle And Other Parts Rotating With Peripheral Speed Of More Than 3m/sec | Yes |
| Spindle Forward/Reverse Drive Transmission Through Hydraulic Friction Clutch | No |
| "Electric Equipment I.e. Motor And Control Gear Suitable For Operation On 415 V, 3 Phase, 50 Hz., 4 Wire, A.C.supply With Suitable Ammeter " | Yes |
| DRIVING PLATE WITH PEG | Yes |
| Coolant Equipment & Swarf Tray | Yes |
| SPLASH GAURD : | Yes |
| SPINDLE REDUCTION SLEEVE: | Yes |
| 60Deg.DEAD CENTRE-2 Nos.: | Yes |
| ROTATING CENTE-1Nos.: | Yes |
| QUICK CHANGE TOOL POST WITH TOOL HOLDERS | Yes |
| QUICK INDEXIBLE SQUARE TOOL POST | No |
| SET OPERTING INSTRUCTION MANUAL& A SET OF OPERATING TOOLS. | Yes |
| 3Jaw Self Centring Chuck | Yes |
| Precision 3 Jaw Self Centring Chuck ( Hydraulic /Pneumatic Complete Chuck ) | No |
| Chuck Gurad | No |
| Rear Tool Post | Yes |
| Universal Face Plate | No |
| Precision Face Plate | No |
| Cast Iron Face Plate | Yes |
| Collet Chuck & Collets. | No |
| Rear Tool Holder. | No |
| Steady Rest. | Yes |
| Roller Steady Rest | No |
| Follow Rest | Yes |
| Longitudinal Stop. | Yes |
| Roller Stop. | No |
| Taper Turning Attachment. | Yes |
| A Set Of Change Gear For DP Threads. | Yes |
| Multi Copying Attachment | No |
| Machine Lamp | Yes |
| Swraf Tray Complete With Coolant Equipment | No |
| Four Jaw Chuck | Yes |
| Availability Of Drawing For Foundation | Yes |
| Warranty | 1 Years |
| Annual Maintenance Contract For Machine | No |
| Period Of AMC | 0 Years |
| Availability Of Test Report From Central Govt./NABL/ILAC Acredited Lab To Prove Confirmity To Specification | Yes |
| Test Report No. | ML-I-456 |
| Test Report Date | 3-1-2018 |
| Name Of The Lab | INSTITUTE FOR MACHINE TOOLS TECHNOLOGY |
| Address Of The Lab | A-4, FOCAL POINT, BATALA |
| Purpose Classification | General Purpose |
| Lathe Machine Type | Center Lathe |
| Main Motor Power ( For Light Duty Lathe ≥ 3kw,For High Speed Precision Lathe ≥ 11kw, For Heavy Duty Lathe ≥ 18kw) | 3.7 kw |
| Erection And Commisioning Charges Included In Offered Prices Without Foundation | Yes |
| Spindle Forward/Reverse Drive Transmission Through Electro Magnetic Double Clutch | No |
| Nature Of Duty Of Operation Of Lathe | High Speed Precision Lathe |
Price Dekho Price List in india© 2018 GeM All rights reserved.
