1. Conformity of Specification to WHO/IVB/11.08 version dated 26/09/2011

2. Vehicle Engine Capacity (cc)

3. Type of Fuel

4. Vehicle Certification ARAI/VRDE/ICAT No.

5. Vehicle Emission Complaince

6. Colour of the Vehicle

7. Vehicle Mileage ( declared by OEM as certified by Test Agency under Rule 115of CMVR 1989),City/Highway (Km/Ltr)

8. Engine BHP@rpm (min.) (HP@rpm)

9. Engine Torque Max,@ rpm (N-M@rpm)

10. No. of Cylinder in Engine

11. Seating Capacity including Driver

12. Doors:Single insulated rear-opening door. Two side-doors in driver cabin, one on each side.

13. Fuel Tank Capacity (Ltrs)

14. Length of Cargo box (mm)

15. Width of cargo box (mm)

16. Height of Cargo Box (mm)

17. Ground Clearance(when fully loaded)(min.) (mm)

18. Wheel Base (mm)

19. Type of Wheel drive

20. Kerb Weight (kg)

21. Gross Weight (kg)

22. Type of Vehicle Tyre

23. Size Of Tyre (mm)

24. Vehicle Transmission System

25. No. of Forward Gears

26. Suspension

27. Type of Steering

28. Turning Radius(meters) (175/65R14 Say)

29. Frame Section

30. Brakes

31. Vehicle Brake ABS Fitted

32. Central Locking

33. Vehicle Air Intake System

34. Driver Airbag

35. Co -Driver Airbag

36. Power Door Locks /security deadlocks with vehicle alarm system

37. Low Fuel warning Light

38. Structure

39. Super structure formed of 16 GMS pressed CR/HR Hot Sections. For side pillars and roof sticks with two sections for anti drumming rails and roof longitudes. Suitably reinforced with gussets and cleats.

40. Floor:-16 G Aluminum Sheet/chequered plate.

41. Paneling:16 g aluminum sheet for exterior and 18g aluminum sheet for interior paneling. All panels shall consist of interior and exterior metal surfaces precision roll formed to exact dimensions to enhance overall panel rigidity. The finished metal surfaces shall be fitted with a profile gasket and placed in precision tooled fixtures where they are injected with foamed-in-place urethane insulation. Curing of the insulating should be at a controlled temperature to provide permanent adhesion to the metal surfaces, allowing uniform foam expansion and to maximize finished panel strength. Panel edges should have a foamed-in-place high density urethane tongue and groove profile to accurately align panels during installation and to assure an air-tight seal. No structural wood, steel, straps or other non-insulating materials shall be used in panel construction.

42. Insulation:100-mm PUF foam on all four sides & floor.Sandwich panels of extruded Polystyrene. Roof of 140 mm thick PU Foam/sandwich panels of extruded Polystyrene having thermal conductivity not more than 0.081 K cal, U value 0.020 W.M.K and density not less than 30 Kg/cum

43. Rear compartment separated from driver s cabin by full partition.

44. Spare wheel mounting

45. The body should be in the aerodynamic shape from the front, Tapered/sloped roof of cargo box to dispense rain water.

46. Footsteps and hand grips at the back for climbing in the cargo box to be provided.

47. IEC information for immunization and child health will be painted on all three outside walls of the box.

48. Inside temperature of the insulated box (in closed condition) should be less than the outside temperature at ambient condition

49. Temperature range of interior of insulated body at any point of time

50. temperature monitoring device with two sensors ,with a traceable certificate of calibration.

51. An Automatic tachograph for driver monitoring

52. Tool kit and user/service manual:Standard tool kit such as lifting jack, wheel spanner, screw driver etc with user service manual.

53. Warranty Time (Months)

54. Warranty Distance (kms)

55. Battery Warranty (Months)

56. No. of Free Service (Nos.)

57. Transportation Charge in Rupees Per Km (Rs/Km)