1-800-419-3436 / 1-800-102-3436 
Support Desk
×
All the transactions performed on 2.0 is available here. To access Market click "Home".
40 GHz Signal Generator.
| Other Specifications Download Specification | |
|---|---|
| Type | RF Signal Generator |
| Frequency Range | 10 MHz to 40 GHz |
| Frequency Resolution | 0,1 Hz |
| Ageing Rate For Reference Frequency (As Declared By OEM) | Less than 2 PPM/Year |
| Temperature Stability For Reference Frequency | Less than 2 PPM |
| SSB Phase Noise At 1GHz,on 20KHz Offset (dBc/Hz) | less than -105 dBc |
| Harmonics At 3 GHz Level At 0 DBm | less than -30 dBc |
| Non Harmonics (>10 KHz Carrier Offset) | less than -60 dBc |
| Non Harmonics (>50 KHz Carrier Offset) | less than -55 dBc |
| Reverse Power Protection | Less than 1 Watt Watt |
| Minimum Output Level | -120 dBm |
| Maximum Output Level | +5 dBm |
| Output Level Resolution | 0,1 dB |
| Total Accuracy Forall Specified Output Level At 25 Degree C In Continuous Wave Mode | ≤±1 dB dB dB |
| VSWR On All Operating Frequencies | 2 |
| Memory (Minimum Storage Settings) | 10 |
| Amplitude Modulation (AM) Operating Modes | Internal & External |
| Minimum Amplitude Modulation Frequency (3 DB), F > 100 KHz | DC to 50 kHz minimum Hz Hz |
| Maximum Amplitude Modulation Frequency (3 DB), F > 100 KHz | DC to 100 kHz typical KHz KHz |
| Modulation Depth | 0 % to 90 % (nominal) % % |
| Resolution Of AM | 10% |
| AM Distortion At 1 KHz | less than < 5 typical |
| Frequency Modulation (FM) Operating Modes | Internal & External |
| Minimum Frequency Modulation Frequency (-3 DB) Standard | Unlocked: DC to 10 MHz Locked:1 kHz to 10 MHz |
| Maximum Frequency Modulation Frequency (-3 DB) Standard | Unlocked: DC to 10 MHz Locked:1 kHz to 10 MHz |
| Minimum Frequency Deviation | DC to 8 MHz |
| Maximum Frequency Deviation | DC to 8 MHz KHz KHz |
| Resolution Of FM | 10% |
| Setting Error (at AF=1 KHz And 50% Max. Deviation) For FM | 10 % (5 % typical) |
| Phase Modulation | Available |
| If Available, Phase Modulation Operatinf Mode | Internal & External |
| Minimum Phase Deviation | DC to 8 MHz Radians Radians |
| Maximum Phase Deviation | 10% Radians Radians |
| Resolution Of Phase Modulation | 1 % |
| Setting Error (at AF=1 KHz) For Phase Modulation | 10% |
| Internal Modulation Generator For AM/FM/PM | 0.1 Hz to 10 MHz sinusoidal 0.1 Hz to 1 MHz square-wave, triangle, ramps 0.1 Hz |
| Pulse Modulation | Not-Available |
| If Available, Pulse Modulation Operating Modes | NA |
| Rise And Fall Time | NA ns |
| On/Off Ratio | NA dB |
| Minimum Pulse Width | NA ns |
| Input Level | NA |
| RF Digital Sweep Range And Width | Width: 8MHz to full range |
| RF Digital Sweep Time Range | 1 ms to 99 s |
| RF Analog Sweep | Not-Available |
| If Available, RF Analog Sweep Range And Width | NA |
| RF Analog Sweep Time Range | NA |
| Pulse Generator | Available |
| If Available, Pulse Generator Operating Mode | Automatic, externally triggered, external gate mode, single pulse, double pulse, delayed pulse(externally triggered) |
| Pulse Width | 10 ns to 1.6 s |
| Pulse Delay | 100 ns to 1.6 s |
| Pulse Period | 100 ns to 1.6 s |
| Vector Modulation | Not-Available |
| Internal Base Band Generator Bandwidth | NA MHz |
| Arbitory Waveform Memory | NA Mega samples |
| Modulation | NA |
| Error Vector Magnitude (EVM) | 0 % |
| Phase Modulator | Available |
| If Available, Range Of Modulating Signal (Wide Mode) | DC to 1 MHz: ± [Lesser of 400 rad |
| If Available, Range Of Modulating Signal (Narrow Mode) | DC to 8 MHz: ± [Lesser of 3 rad |
| Interface Available | IEEE 488 & LAN |
| Standard Acessories (To Be Supplied) | "Software for MG3690X Operation Manual Programming Manual SCPI Programming Manual IVI Drivers Technical Datasheet CAT-7 shielded, twisted-pair, Ethernet cable, 10 ft. Power Cord with plug-type" |
| Power Requirements | 230 V +/-10% AC, 50 Hz +/- 3% |
| Operating Temperature Range | 0 °C to +50 °C Degree C Degree C |
| Operating Humidity (RH) | 5 % to 95 % % % |
| "Availability Of Test Reports From Central Govt / NABL Approved / ILAC Acredited Lab To Prove Conformity To The Specification Including Environmental Tests As Under : 1. Dry Heat Test : 45 Deg C For 16 Hours As Per IS:9000/Pt.3/sec.5/1977 (reaffirmed In 2007) 2. Cold Test : 0 Deg C For 4 Hours As Per IS:9000/Pt.2/sec.4/1977 (reaffirmed In 2007) 3. Damp Heat Test: 95% RH At 45 Deg C, Two Cycles Of 24 Hours Each Separated By A Gap Of 4 Hours As Per IS:9000/Pt.5/sec. 1/1991 (reaffirmed In 2007) All The Functional Paramteres Are To Be Verified Before And After Recovery Period Of 1 Hours Of Above Environmental Test Sequence As Above. There Shall Be No Deterioration In Functional Parameters. | Yes |
| Test Report No. | A2LA Cert. No. 2160.01 |
| Test Report Date | 06/01/2016 |
| Name Of The Lab | Anritsu Company, 490, Jarvis Drive, Morgan Hill, CA 95037 USA |
| Warranty | 3 Years |
Price Dekho Price List in india© 2018 GeM All rights reserved.
